Wooden Garage

How To Troubleshoot Your Garage Door In 10 Steps?

Garage doors are a crucial part of your home. Not only do they keep your car safe, but they also provide security for your home. If something goes wrong with your garage door, it can be very frustrating. In this article, we will walk you through the steps to troubleshoot your garage door in case of a problem. So, read on.

How To Troubleshoot Your Garage Door In 10 Steps?

Ways To Troubleshoot Your Garage Doors

If you have a garage door that's giving you trouble, it can be frustrating trying to figure out what the problem is. However, there are some ways that you can troubleshoot your garage door to try and figure out what the issue is. 


Here are the ten steps on how to troubleshoot your garage door:


1. Check the power.

Make sure that your garage door is getting power by checking to see if the light above the door is on. If it's not, check your circuit breaker box and make sure that the switch for your garage is turned on. If you have a manual garage door, make sure that the cord isn't frayed and that there isn't any damage to the cable drums. If you're using a remote control to open or close your garage door, check the batteries in the remote and replace them if necessary. Also, try pointing the remote at the opener sensor to see if it's working properly.


2. Check the tracks.

If your garage door isn't moving, it could be because something is blocking the tracks. Take a look at the tracks and see if there's anything in the way. If you see something, remove it and try opening or closing your garage door again. It's also possible that the tracks are damaged or bent. If this is the case, you'll need to call a professional to come and fix them for you.


3. Check the rollers.

If your garage door is sticking, it could be because the rollers are dirty or rusty. Try cleaning them off with a damp cloth and see if that solves the problem. If they're too badly damaged, you'll need to replace them. It's also possible that the bearings in the roller are bad and need to be replaced. 


You can tell if this is the case by listening to a grinding noise when the garage door is opening or closing. The brackets that hold the rollers in place could also be loose, which would cause the door to stick. Check these brackets to make sure they're tight and then try opening and closing your garage door again.


4. Check the hinges.

If your garage door is sagging, it could be because the hinges are loose. Take a look at the screws on the hinges and make sure they're tight. If they're not, tighten them up with a screwdriver. It's also possible that the screws have come loose over time and need to be replaced altogether.


5. Check the springs.

If your garage door isn't opening or closing all the way, it could be because the springs are damaged or broken. If you see that the springs are damaged, you'll need to call a professional to come and replace them.


6. Consider checking the sensors.

If your garage door is reversing on its own, it could be because the sensors are dirty or misaligned. Try cleaning them off with a damp cloth and see if that solves the problem. If they're still not working properly, you may need to realign them. 


You can do this by following the instructions in your garage door's manual. It's also possible that something is blocking the sensor beam from hitting the other sensor. If this is the case, try moving whatever is blocking it and see if that solves the problem. Lastly, make sure that both of your sensors are plugged into an outlet and turned on.


7.  Check the opener.

If your garage door is opening and closing slowly, it could be because the opener is overloaded. Try unplugging any appliances or devices that are plugged into the same outlet as the opener and see if that solves the problem. If it doesn't, you may need to get a new opener.


8. Check the chain.

If your garage door opener is making a loud noise, it could be because the chain is loose. Check the chain to see if it's connected properly and if it's not, reconnect it. It's also possible that the sprocket on the motor shaft is damaged or worn out. If this is the case, you'll need to replace it.


9.  Check the panels.

If your garage door is damaged, it could be because one of the panels is bent or dented. Try straightening out the panel with a hammer and see if that solves the problem. If it's too badly damaged, you'll need to replace it. You can find replacement panels at your local hardware store.


10.  Have a professional come and inspect your garage door.

If you've tried all of the steps listed above and your garage door is still not working properly, it's time to call a professional. They'll be able to inspect your garage door and determine what's wrong with it. They may need to order parts or replace entire sections of the door to get it up and running again.


If you’re experiencing problems with your garage door, don’t worry. There are a few steps you can take to troubleshoot the issue yourself before calling in a professional. We’ve outlined the ten ways to troubleshoot your garage doors. So, if your door isn’t opening or closing correctly, give these steps a try. And if all else fails, don’t hesitate to call us for help, we’re here to serve you.

Do You Need a Garage Door Repair Team You Can Trust?


Garage door spring snapped? Garage door stuck? We know how frustrating that experience can be.  Bay Area Doors has been helping customers solve their garage door problems for over 20 years! We have seen it all, and fixed it all! We are pros at Garage Door Installation, Garage Door Repair, Roller repair, Opener repair, and Track replacement. If you have one of these problems, now you know who to call.  Over the years we have helped thousands of SF Bay Area residents and have tons of five star reviews on Google, Yelp, Nextdoor and more.  Whatever the problem, Bay Area Doors is the one to call for garage door repair throughout the San Francisco Bay Area. Contact us today!